Damn - need a change of shorts now.. Controller MK II
-
Dudley
- Master
- Posts: 675
- Joined: Sun Feb 22, 2015 6:25 pm
- CMDR: Dudley_Dawg
- CMDR_Platform: None Specified
- Contact:
Re: Controller MK II
Damn - need a change of shorts now.. As a tribute to Tor, my CMDR has small feet too! o7 Dawg
-
Cmdr Kharma
- Dangerous
- Posts: 3776
- Joined: Thu Sep 18, 2014 7:28 pm
- CMDR: Kharma
- CMDR_Platform: PC-MAC
- Contact:
Re: Controller MK II
Just a little heads up......
If you have a series of panel layout printouts laying around.......Destroy all but the latest one......
Took all measurements off of the final one.........Bar one......
Musta picked up the wrong sheet....
Cut all the holes and screw holes......
Looked at it and went WTF......1mm out.....
Trouble is sticks out like a sore thumb......
Fuck it........
I'm gonna continue building it anyway......Had a few blingy ideas for Mk III last night as I was working on it....
*Edit*
I have a plan....To bring it back into alignment.......
Just gotta see if it's possible and what it will look like.....
If you have a series of panel layout printouts laying around.......Destroy all but the latest one......
Took all measurements off of the final one.........Bar one......
Musta picked up the wrong sheet....
Cut all the holes and screw holes......
Looked at it and went WTF......1mm out.....
Trouble is sticks out like a sore thumb......
Fuck it........
I'm gonna continue building it anyway......Had a few blingy ideas for Mk III last night as I was working on it....
*Edit*
I have a plan....To bring it back into alignment.......
Just gotta see if it's possible and what it will look like.....
Tor.....Hold on.......Tor.......Wait a bit.....TOR will you stop fecking firing.......Ok......Tor I know a therapist that can help you.......
My Cmdr also has small feet-
Cmdr Kharma
- Dangerous
- Posts: 3776
- Joined: Thu Sep 18, 2014 7:28 pm
- CMDR: Kharma
- CMDR_Platform: PC-MAC
- Contact:
Re: Controller MK II
Ok time to update.....
I cut the rectangular holes for the switches and did a test fit.....
Notice the cock ups......Look at the right hand panel switches.....I had to raise them because they hit on the base.....No prob as I can fill them as seen on the right hand one......
Also the bottom set of the ramp switches hit on the top panel.....No prob again...Just needed a cut out....
Secured the right hand side ramp support....
Drilled the rest of the holes and mounting bolt holes and test fitted......It was a this point I noticed the wrong measurement.....The nav button hole is 1mm out.....
I do have a way to fix it but It's not as pretty as I would have liked.......
T.B.C
*Edit*
The rest to follow.....Looks like the camera SD card is failing.....Some later pics are corrupt.....Just backing all on the camera up and going to format card....
I cut the rectangular holes for the switches and did a test fit.....
Notice the cock ups......Look at the right hand panel switches.....I had to raise them because they hit on the base.....No prob as I can fill them as seen on the right hand one......
Also the bottom set of the ramp switches hit on the top panel.....No prob again...Just needed a cut out....
► Show Spoiler
Secured the right hand side ramp support....
► Show Spoiler
Drilled the rest of the holes and mounting bolt holes and test fitted......It was a this point I noticed the wrong measurement.....The nav button hole is 1mm out.....
► Show Spoiler
I do have a way to fix it but It's not as pretty as I would have liked.......
T.B.C
*Edit*
The rest to follow.....Looks like the camera SD card is failing.....Some later pics are corrupt.....Just backing all on the camera up and going to format card....
Last edited by Cmdr Kharma on Thu Sep 15, 2016 8:36 pm, edited 1 time in total.
Tor.....Hold on.......Tor.......Wait a bit.....TOR will you stop fecking firing.......Ok......Tor I know a therapist that can help you.......
My Cmdr also has small feet-
Cmdr Kharma
- Dangerous
- Posts: 3776
- Joined: Thu Sep 18, 2014 7:28 pm
- CMDR: Kharma
- CMDR_Platform: PC-MAC
- Contact:
Re: Controller MK II
Back on track.......
Slotted some cross pieces into the banks of buttons.....
It's easier to cut a complete rectangle and put these in afterwards than to try cutting the individual squares..
Unless you have a laser of course.....
In work a plant room was cleared and the rubbish bought back to the workshop......
I of course had a nosey......An old nurse call system had been replaced and the old one was to be dumped....
Took a look through the panels and found some connectors that looked a bit handy....
T.B.C
Slotted some cross pieces into the banks of buttons.....
It's easier to cut a complete rectangle and put these in afterwards than to try cutting the individual squares..
Unless you have a laser of course.....
► Show Spoiler
► Show Spoiler
In work a plant room was cleared and the rubbish bought back to the workshop......
I of course had a nosey......An old nurse call system had been replaced and the old one was to be dumped....
Took a look through the panels and found some connectors that looked a bit handy....
► Show Spoiler
T.B.C
Tor.....Hold on.......Tor.......Wait a bit.....TOR will you stop fecking firing.......Ok......Tor I know a therapist that can help you.......
My Cmdr also has small feet-
Cmdr Kharma
- Dangerous
- Posts: 3776
- Joined: Thu Sep 18, 2014 7:28 pm
- CMDR: Kharma
- CMDR_Platform: PC-MAC
- Contact:
Re: Controller MK II
I found out the black cap on top was removable and it was a sorta splice connection.....
Handy as the wires can be pulled out and I tried the wire I have and it fits perfect.....
Also it was the same pitch as the PCB headers I had......
So I ordered some headers with long pins both sides...Rather than through the board type like I had....
Idea is to link the interface to the buttons/switches like this to provide complete easy removal or reconfiguration, no need to undo anything..
And that's it for now......
T.B.C
► Show Spoiler
Handy as the wires can be pulled out and I tried the wire I have and it fits perfect.....
Also it was the same pitch as the PCB headers I had......
So I ordered some headers with long pins both sides...Rather than through the board type like I had....
► Show Spoiler
Idea is to link the interface to the buttons/switches like this to provide complete easy removal or reconfiguration, no need to undo anything..
► Show Spoiler
And that's it for now......
T.B.C
Tor.....Hold on.......Tor.......Wait a bit.....TOR will you stop fecking firing.......Ok......Tor I know a therapist that can help you.......
My Cmdr also has small feet-
Dudley
- Master
- Posts: 675
- Joined: Sun Feb 22, 2015 6:25 pm
- CMDR: Dudley_Dawg
- CMDR_Platform: None Specified
- Contact:
Re: Controller MK II
Cmdr Kharma wrote:I found out the black cap on top was removable and it was a sorta splice connection.....
Handy as the wires can be pulled out and I tried the wire I have and it fits perfect.....
Also it was the same pitch as the PCB headers I had......
So I ordered some headers with long pins both sides...Rather than through the board type like I had....
Idea is to link the interface to the buttons/switches like this to provide complete easy removal or reconfiguration, no need to undo anything..
And that's it for now......
T.B.C
Right.. now stop that!! 
You are obviously enjoying yourself and you know that, THAT IS NOT ALLOWED..!!
You are to continue, but only in a grumpy manner!!!
o7 Dawg
As a tribute to Tor, my CMDR has small feet too! o7 Dawg
-
Cmdr Kharma
- Dangerous
- Posts: 3776
- Joined: Thu Sep 18, 2014 7:28 pm
- CMDR: Kharma
- CMDR_Platform: PC-MAC
- Contact:
Re: Controller MK II
Took your advice.......
And glued the very last front panel bit on the wrong way around......
Arghhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh.............
And glued the very last front panel bit on the wrong way around......
Arghhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh.............
Tor.....Hold on.......Tor.......Wait a bit.....TOR will you stop fecking firing.......Ok......Tor I know a therapist that can help you.......
My Cmdr also has small feet-
Dudley
- Master
- Posts: 675
- Joined: Sun Feb 22, 2015 6:25 pm
- CMDR: Dudley_Dawg
- CMDR_Platform: None Specified
- Contact:
Re: Controller MK II
Cmdr Kharma wrote:Took your advice.......
And glued the very last front panel bit on the wrong way around......
Arghhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh.............
Good man...that's more like it!!
o7 Dawg
As a tribute to Tor, my CMDR has small feet too! o7 Dawg
-
Cmdr Kharma
- Dangerous
- Posts: 3776
- Joined: Thu Sep 18, 2014 7:28 pm
- CMDR: Kharma
- CMDR_Platform: PC-MAC
- Contact:
Re: Controller MK II
Everything was going fine till you opened your gob......
Now I can't find my countersink bit......
I swear.....
Once back in game.....
I'm gonna pop a cap in yo ass......
PVP stylee.......
Now I can't find my countersink bit......
I swear.....
Once back in game.....
I'm gonna pop a cap in yo ass......
PVP stylee.......
Tor.....Hold on.......Tor.......Wait a bit.....TOR will you stop fecking firing.......Ok......Tor I know a therapist that can help you.......
My Cmdr also has small feet-
Dudley
- Master
- Posts: 675
- Joined: Sun Feb 22, 2015 6:25 pm
- CMDR: Dudley_Dawg
- CMDR_Platform: None Specified
- Contact:
Re: Controller MK II
Cmdr Kharma wrote:Everything was going fine till you opened your gob......
Now I can't find my countersink bit......
I swear.....
Once back in game.....
I'm gonna pop a cap in yo ass......
PVP stylee.......
Welcome back sir.. o7 Dawg
As a tribute to Tor, my CMDR has small feet too! o7 Dawg
Return to “Hardware and Technical”
Who is online
Users browsing this forum: No registered users and 77 guests